2 620-7920 Rev A STAR TRAC 14410 Myford Road Irvine, CA 926060 USA WORK INSTRUCTIONS, E-TRx / E-TRxe INSTALLATION
11 620-7920 Rev A Step 17. Now tighten the 4 display rail fasteners (where neck is joined with display rail) to a torque value of
12 620-7920 Rev A Step 22. Secure the front of the motor shroud with (2) #10 Truss head screws. Step 23. Now secure the sides of the
13 620-7920 Rev A Step 27. Secure the power cable to the frame with the tie-strap and cut excess strap. Caution: Make sure not to damage the
14 620-7920 Rev A Step 1. Remove electronic display console from pack-aging materials. Note: If you are installing an iPod® Kit, a MYE En
15 620-7920 Rev A Step 5. Connect the E-Stop cable (g) to J25 connector on the display board, then connect the rail stop cable (f) to J5 connec
16 620-7920 Rev A Step 9. Connect the main I/O cable (e) to J1 connector on the display board. Step 10. Mount the display assembly to the
17 620-7920 Rev A Step 13. Install the top back cover piece (p/n 020-7074) onto the upper display back cover (p/n 020-7069). Step 14. I
18 620-7920 Rev A ATTENTION • Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy
19 620-7920 Rev A THIS PAGE INTENTIONALLY LEFT BLANK
20 620-7920 Rev A Step 2. Take out the embedded display console out of the box and remove all packing material. Verify no visual damage
3 620-7920 Rev A GENERAL Before using this product, it is essential to read ALL installation Instructions and this ENTIRE operations manual; th
21 620-7920 Rev A Step 8. Position the display assembly near the top rail while a helper makes the necessary connec-tions. Step 11.
22 620-7920 Rev A Step 13. Connect the E-Stop cable (g) and the Contact Heart Rate cable (c) to respective connectors on the FitCpu boar
23 620-7920 Rev A Step 16. Connect the I/O interface cable (e) to J1 connec-tor on the translator board located on the top of the embedded disp
24 620-7920 Rev A Step 21. If not done already, position the treadmill where you plan to use it. If necessary, level the tread-mill using th
25 620-7920 Rev A ATTENTION • Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy
26 620-7920 Rev A THIS PAGE INTENTIONALLY LEFT BLANK
27 620-7920 Rev A Step 3. If the display console is already installed on the frame and the back enclosures are off, remove the screws to rel
28 620-7920 Rev A Step 5. Using a Phillips head screw driver, remove the screw that holds in the headphone jack cap at the lower front
29 620-7920 Rev A Step 9. Install the new iPod® center console. Step 10. Connect headphone cable coming from Hot Bar rail to the headphone
30 620-7920 Rev A Step 16. Install and secure lower back cover then turn power on. Perform a visual inspection, and test the features
4 620-7920 Rev A Step 3. Remove the side box. Step 4. Lay all boxes on the floor and verify that all components are included (se
31 620-7920 Rev A ATTENTION • Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy
32 620-7920 Rev A THIS PAGE INTENTIONALLY LEFT BLANK
33 620-7920 Rev A Step 3. If the display console is already installed on the frame and the back enclosures are off, remove the screws to rel
34 620-7920 Rev A Step 5. Using a Phillips head screw driver, remove the screw that holds in the headphone jack cap at the lower front
35 620-7920 Rev A Step 10. Connect the headphone cable coming from Hot Bar rail to the headphone connector on the MYE® center console. Step 9.
36 620-7920 Rev A Step 16. Turn power on. Perform a visual inspection, and test the features and functions of the unit prior to use. Note: R
37 620-7920 Rev A ATTENTION • Star Trac recommends that the treadmill be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy
38 620-7920 Rev A THIS PAGE INTENTIONALLY LEFT BLANK
39 620-7920 Rev A Step 2. Verify following items included in hardware kit: 1. (1) Silicon wrap 2. (2) Tie strap 3. (1) M8 nut 4. (1) 5MM H
40 620-7920 Rev A Step 5. Connect the coax cable coming the treadmill neck to the coax cable coming from the PVS neck, secure t
5 620-7920 Rev A Step 7. Verify components in box two (continued): 1.Neck cover. 2.Display console’s top back cover (p/n 020-7074). 3.Neck gro
41 620-7920 Rev A Step 10. Using a Phillips head screw driver, remove the screw that holds in the headphone jack cap at the lower front of
42 620-7920 Rev A Step 13. Select the E-TRx headphone mount from the kit and attach it to the available cut-out at the lower front of the hot b
43 620-7920 Rev A Step 17. Plug the center console’s 7-pin interface cable into J11 connector on the display board. Step 19. Plug the center c
44 620-7920 Rev A Step 24. Turn power on. Perform a visual inspection, and test the features and functions of the unit prior to use. Note: R
45 620-7920 Rev A ATTENTION • Star Trac recommends that treadmills be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingr
46 620-7920 Rev A STAR TRAC 14410 Myford Road Irvine, California 92606 Telephone: (800) 228-6635, (714) 669-1660 Fax: (714) 508-3303 http
STAR TRAC FITNESSTME-TR TreadmillO WNER’ S M ANUAL
After having used your STAR TRAC E SERIES TREADMILL for many workouts, you may wish to change some of its settings.MANAGER MODEThe Manager Mode allows
*When the MINIMUM SPEED or MAXIMUM SPEED parameters are changed, the Treadmill will perform an auto calibration. To termi-nate the auto calibration an
Enter Key: Updates (saves) the value of the displayed parameter in Flash memory. Alternatively, the key may beused (see above).Number/Program Select
6 620-7920 Rev A Step 9. Verify the following tools are included in the hardware kit : Step 10. Verify hardware included in the hardware kit
*When the MINIMUM SPEED or MAXIMUM SPEED parameters are changed, the Treadmill will perform an auto calibration. To termi-nate the auto calibration an
ELEVATION CALIBRATIONThe Elevation Calibration function allows for calibration of the treadmill's elevation function. To enter the Elevation Cali
TROUBLESHOOTING42 STAR TRAC E SERIES TREADMILL OWNER’SMANUALStar Trac recommends that you refer your questions about your STAR TRAC E SERIES TREADMILL
7 620-7920 Rev A Step 3. Position neck close to the service opening in the front of treadmill so the cables go into the opening
8 620-7920 Rev A Step 6. Align the front holes and fasten with (2) 5/16-18 x 3.0”, (2) 5/16 washers and (2) lock washers. DO NOT fully
9 620-7920 Rev A Step 10. Now install the top display rail. Align the rail’s mounting holes with the neck holes. Note: If the elect
10 620-7920 Rev A Step 15. Now tighten the 2 front neck screws (5/16-18 x 3.0” socket head) to a torque value of 200 in-lbs (22.5 Nm). Ste
Comments to this Manuals